Pipes Hydrostatic Pressure Testing Machine

Pipes Hydrostatic Pressure Testing Machine

(10-60MPa, PVC, Π.Ε, σωλήνα κλπ, 3 -40σταθμούς ή περισσότερους, 15℃- 95℃, έλεγχος υπολογιστή αφής)

1.Εισαγωγή

Pipes Hydrostatic Pressure Testing Machine is a device specially designed to test the load-bearing capacity and sealing performance of HDPE, PVC, Π.Ε, PPR, ABS and other plastic pipes under hydrostatic pressure. It is widely used in water conservancy, petroleum, chemical industry, construction and other fields, and is essential to ensure the quality and safety of pipes. The following is a detailed introduction to the working principle and international testing standards of the pipe hydrostatic testing machine.

Pipes Hydrostatic Pressure Testing Machine

Working principle

The working principle of Pipes Hydrostatic Pressure Testing Machine is mainly to apply gradually increasing pressure to the pipe through hydrostatic pressure test to detect its ability to withstand pressure and potential defects. The specific steps include:

1. Preparation: Clean the fixture and the surface of the pipe, put the pipe to be tested into the center of the fixture and clamp it, and check whether the hydraulic pump and control system are normal.

2. Start the equipment: Start the hydraulic pump to make the hydraulic cylinder slowly apply internal pressure to the pipe. When the internal pressure reaches the preset value, the pressure sensor transmits the internal pressure value to the control system.

3. Adjust the internal pressure: Adjust the parameters in the control system as needed, such as the internal pressure rise and fall speed, pressure holding time, και τα λοιπά.

4. Monitor the internal pressure: Monitor the internal pressure value of the pipe in real time through the control system to ensure that the internal pressure value is stable and does not exceed the pressure resistance range of the pipe.

5. Record data: When the pipe is damaged, the pressure sensor will transmit the damage pressure value to the control system, record the damage pressure value, as well as the wall thickness, pipe diameter, damage position and other parameters of the pipe.
6. Stop the equipment: When the test is completed, stop the hydraulic pump and control system, and turn off the power to the equipment.

pipes Hydrostatic Pressure Testing Machine Test standards: ISO 1167, ASTM D1598, ASTM D1599, ASTM D1784, ASTM D2466, ASTM F442, ASTM D2672,ASTM D2837,ASTM D2992,ASTM D2517,ASTM D2241,ASTM D3139,ASTM D3212,ASTM D1599,ASTM D2846,ASTM D2846M,NTC382.

2. Βασικές τεχνικές παράμετροι(Pipes Hydrostatic Pressure Testing Machine)

2.1 Εύρος πίεσης: 0.2MPa -60 MPa, άλλη μονάδα πίεσης είναι διαθέσιμη όπως η μπάρα, PSI

2.2. Ανάλυση δοκιμής πίεσης: 0.001MPa, 1PSI, 0.01Μπαρ

2.3. Ακρίβεια ελέγχου πίεσης: -1% ~ +2%

2.4. Δοκιμαστικός σωλήνας: φ16 – φ1600mm,1/8Inch-64Inches

2.5. Δοκιμαστικός σταθμός: 3 σταθμούς (τυπική παροχή) ή ακόμα περισσότερο

2.6. Χρονικό εύρος: 0 – 10000η, θετικό χρονοδιάγραμμα ή αντίστροφη μέτρηση, ελάχιστη κλίση χρόνου ρύθμισης 1 ελάχ.

2.7. Τροφοδοτικό της μηχανής υποδοχής: 1- φάση, 220V±10%, 50Hz, 0.5kW

2.8 Τροφοδοσία σταθμού πίεσης: 3-φάση, 380V±10%, 50Hz, 5kW

3. Χαρακτηριστικά

Pipes Hydrostatic Pressure Testing Machine is a multi-purpose machine that can test the long-term hydrostatic pressure of pipelines, perform pipe burst tests, and determine the thermal stability of thermoplastic pipes. It has multiple control modes, such as run, stop, leakage, overpressure warning, and rupture identification, so that operators can leave the test site during the test. When the sample leaks or ruptures, it will automatically alarm and automatically close the circuit, while other circuit tests will continue normally until the test is completed.

Επικοινωνήστε μαζί μας:
Τζέρι Ζανγκ
Κινητό: +86-13853148617
WeChat & WhatsApp: +86-13853148617
ΗΛΕΚΤΡΟΝΙΚΗ ΔΙΕΥΘΥΝΣΗ: sales06@victorytest.com
Δικτυακός τόπος: http://www.victorytestgroup.com